A new pattern based on an old design of mine (Elements armwarmers), these fingerless mitts have been re-knitted and updated almost ten years after I published the pattern.
I have used Scheepjes Stone Washed XL which is 70% cotton, 30% acrylic. I bought a box of 50 mini skeins, along with five 50g balls of the cream, and after I finished crocheting a sweater I had lots left over. The original mitts were made with a colour-changing yarn, so there were way fewer tails to weave in. Of course you can use whatever aran weight yarn you like.
The weight of these when finished is 80 grams so you could just use one 100g skein of yarn. Or you can go nuts with colour, like I did!
What you’ll need:
100g aran weight yarn, either all one colour or a combination
5mm/US8 needles, either a long circular for magic loop or dpns
Designed to fit a 7.75” hand, measured around the palm above the thumb, a 6” wrist and 10.5” forearm.
Finished dimensions 6.5” around hand, 7” at wrist, 9” at forearm. Total length 11”.
The first rendition of the pattern stretched out considerably around my hand, so I’ve remade it with less ease. Once you know your gauge, it’s a simple case of adjusting the numbers to fit your own arms.
13sts/3” (4.33sts/inch) and 7 rows/inch.
No need to knit a gauge swatch – this project is small enough that you can start knitting and measure your stitch gauge after the first inch of stockinette/stocking stitch. Row gauge is not crucial as you are knitting to measurements. And you can try on as you go.
CO cast on
BO bind off
K2tog knit 2 together (decrease)
dpns double pointed needles
Cast on 42 stitches and either divide them between your dpns or set up your circular needle for magic loop. (Pro tip – make sure each needle starts with a knit stitch, not a purl stitch.) Join in the round. Work K1, P1 ribbing for 5 rounds. (42 sts)
Change to stockinette (knit all stitches) and work 7 rounds. (42 sts)
Next round: dec by K2tog in two places while working this round (I positioned my decs randomly, just trying to make sure they weren’t stacking above each other in subsequent rounds. If you’d rather do all decs at beg and end of round, then feel free to do so.) (40 sts)
**K 7 rounds, work dec round; repeat from ** four times. (32 sts)
K straight until your work measures 10”, or desired length to base of thumb, from cast on edge.
(My original design made two identical mitts – this time I positioned the thumbholes differently so that the colour jogs were not running along the top of my hand – it’s your choice as to what you do here.)
Left mitt: BO 8 sts, K to end of round. (24 sts)
Right mitt: K to 8 sts from end of round, BO 8 sts (24 sts)
Next round: K around, use knitted cast on method to CO 6 or 7 sts over the gap created by the BO in the last round. (I did 6, it was pretty snug, again it depends on the fit you want.)
The thumbhole rounds may need some finagling on your needles. You may need to shift stitches around on your dpns/circs to make it easier to BO and CO these stitches.
K 5 rounds, or more for more coverage. (The original design had ribbing at the hand – I ended up ripping and redoing three times because it looked messy and went with continuing the stockinette instead.)
Bind off. Weave in ends (or knot and trim if you’re lazy like me).
Notes on colour: I chose to work the initial ribbing in one colour, then do 3 row stripes of each colour, and then the thumbhole and last 5 rows in one colour. I couldn’t tell you what the names of these colours are as the labels came off when I made the sweater. And my mitts are fraternal rather than identical twins!